Notifications and Certifications

This appendix provides the FCC and ISED notices, RF exposure requirements, approved radio transmitter and antenna lists, and safety certifications for each Pro Series device.

EPC Notifications

This section contains the notifications for the Endpoint Controller (EPC). The next section contains the notifications for the Safety Remote Control Pro (SRC Pro).

FCC Notifications (EPC)

CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation.

Note:

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

RF Exposure Information (EPC)

To comply with FCC/IC RF exposure limits for general population/uncontrolled exposure, the antenna(s) used for this transmitter must be installed to provide a separation distance of at least 20 cm from all persons and must not be co-located or operating in conjunction with any other antenna or transmitter.

ISED (EPC)

The radio transmitters in the following table have been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed in the next table, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Les émetteurs radio du tableau suivant ont été approuvés par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d’antennes répertoriés dans le tableau suivant, avec le gain maximum autorisé indiqué. Les types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l’exploitation de l’émetteur.

Approved radio transmitters:

Table 1. Table 93 EPC Approved Radio Transmitters
Function	Part #	FCC	ISED	Products
900MHz ISM	100-0235	2A8I8-100235	29381-100235	EPC/SRCP/WES/NSC
WiFi/BT	CMP9377-UA	W7Z-WB609102	8254A-WB609102	EPC
LR BLE	BT832X	X8WBT832XE	4100A-BT832XE	SRCP/EPC/WES

The following table shows antenna type(s) that can be used with the transmitter (note that antennas are under review and subject to change):

Table 2. Table 94 EPC Approved Antenna Types
Manufacturer	Antenna Type	Model	Gain (dBi)	Impedance (Ω)
Linx Technologies Inc	Dipole, 1/2 Wave, Whip, Straight Antenna	ANT-915-IPW1-RPS	2.7	50
Linx Technologies Inc	Dipole, 1/2 Wave, Whip, Straight Antenna	ANT-2.4-CW-HWR-RPS	3.2	50
Linx Technologies Inc	Dipole, 1/2 Wave, Dual Band, Dome	ANT-W63-SPNF1	4.5 @ 2.4GHz 7.2 @ 5.0GHz	50

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

L’émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d’Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L’exploitation est autorisée aux deux conditions suivantes :

L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

RF Exposure Requirements (EPC)

This equipment complies with ISED RSS-102 radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body.

Cet équipement est conforme aux limites d’exposition aux rayonnements ISED établies pour un environnement non contrôlé. Cet équipement doit être installé et utilisé avec un minimum de 20cm de distance entre la source de rayonnement et votre corps The transmitter module may not be co-located with any other transmitter or antenna. Le module émetteur peut ne pas être coïmplanté avec un autre émetteur ou antenne.

The declaration of conformity is available upon request.

EPC Certification

The EPC has been certified as SIL 3 for functional safety (per IEC 61508) by exida® corporation.

SRC Pro Notifications

This section contains the notifications for Safety Remote Control Pro (SRC Pro). The next section contains the notifications for the Endpoint Controller (EPC).

FCC Notifications (SRC Pro)

CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference and
This device must accept any interference received, including interference that may cause undesired operation.

Note:

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

RF Exposure Information (SRC Pro)

This portable device complies with FCC RF exposure limits for general population/uncontrolled exposure. To ensure compliance, only use an authorized antenna type listed in this manual with this product. Use of an antenna type other than those specified may result in RF exposure levels exceeding the FCC requirements for RF exposure.

ISED (SRC Pro)

Approved radio transmitters:

Table 3. Table 95 SRC Pro Approved Radio Transmitters
Function	Part #	FCC	ISED
900MHz ISM	100-0235	2A8I8-100235	29381-100235
BT	BMD-300-A-R	2AA9B04	12208A-04
LR BLE	100-0308	2A8I8-1000308-1	29381-1000308A

Antenna type(s) that can be used with the transmitter (note that antennas are under review and subject to change):

Table 4. Table 96 SRC Pro Approved Antenna Types
Manufacturer	Antenna Type	Model	Gain (dBi)	Impedance (Ω)
Linx Technologies Inc	Dipole, 1/2 Wave, Whip, Straight Antenna	ANT-915-IPW1-RPS	2.7	50
Linx Technologies Inc	Dipole, 1/2 Wave, Whip, Straight Antenna	ANT-2.4-CW-HWR-RPS	3.2	50
Linx Technologies Inc	Dipole, 1/2 Wave, Dual Band, Dome	ANT-W63-SPNF1	4.5 @ 2.4GHz 7.2 @ 5.0GHz	50

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

RF Exposure Requirements (SRC Pro)

This portable device complies with ISED RF exposure limits for general population/uncontrolled exposure. To ensure compliance, only use an authorized antenna type listed in this manual with this product. Use of an antenna type other than those specified may result in RF exposure levels exceeding the ISED requirements for RF exposure.

The declaration of conformity is available upon request.

SRC Pro Certification

The SRC Pro has been certified as SIL 3 for functional safety (per IEC 61508) by exida® corporation.

WES Pro Notifications

This section provides notifications and certifications regarding the WES Pro.

FCC Notifications WES Pro

CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference and
This device must accept any interference received, including interference that may cause undesired operation.

CAUTION:

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

RF Exposure Information WES Pro

ISED (WES Pro)

This radio transmitter (IC: 29381-1000415A) has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Le présent émetteur radio [IC: 29381-1000415A] a été approuvé par Innovation, Sciences et Développement économique Canada pour fonctionner avec les types d’antenne énumérés ci dessous et ayant un gain admissible maximal. Les types d’antenne non inclus dans cette liste, et dont le gain est supérieur au gain maximal indiqué pour tout type figurant sur la liste, sont strictement interdits pour l’exploitation de l’émetteur

Approved radio transmitter(s):

Table 5. Table 97 WES Pro Approved Radio Transmitters
Function	Part #	FCC	ISED	Products
HP BLE	BT832X	X8WBT832XE	4100A-BT832XE	SRCP/EPC/WES

Antenna type(s) that can be used with the transmitter:

Table 6. Table 98 WES Pro Built-in Antenna
Manufacturer	Antenna Type	Model	Gain (dBi)	Impedance (Ω)
Pasternack	Rubber duck, omnidirectional	PE51RD1021	2.0	50

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

L’appareil ne doit pas produire de brouillage;
L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en compromettre le fonctionnement.

RF Exposure Requirements WES Pro

The declaration of conformity is available upon request.

WES Pro Certification

The WES Pro has been certified as SIL 3 for functional safety (per IEC 61508) by exida® corporation.

NSCP Notifications

This section contains the notifications for the Nano Safety Controller Pro (NSCP).

FCC Notifications (NSCP)

CAUTION:

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

This device may not cause harmful interference
This device must accept any interference received, including interference that may cause undesired operation.

Note:

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

RF Exposure Information (NSCP)

ISED (NSCP)

Approved radio transmitters:

Table 7. Table 93 NSCP Approved Radio Transmitters
Function	Part #	FCC	ISED	Products
900MHz ISM	100-0235	2A8I8-100235	29381-100235	EPC/SRCP/WES/NSC
LRBLE	BT832X	X8WBT832XE	4100A-BT832XE	EPC

The following table shows antenna type(s) that can be used with the transmitter (note that antennas are under review and subject to change):

Table 8. Table 94 NSCP Approved Antenna Types
Manufacturer	Antenna Type	Model	Gain (dBi)	Impedance (Ω)
Linx Technologies Inc	Dipole, 1/2 Wave, Whip, Straight Antenna	ANT-915-IPW1-RPS	2.7	50
Linx Technologies Inc	Dipole, 1/2 Wave, Whip, Straight Antenna	ANT-2.4-CW-HWR-RPS	3.2	50
Linx Technologies Inc	Dipole, 1/2 Wave, Dual Band, Dome	ANT-W63-SPNF1	4.5 @ 2.4GHz 7.2 @ 5.0GHz	50

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

RF Exposure Requirements (NSCP)

The declaration of conformity is available upon request.

NSCP Certification

The NSCP has been certified as SIL 3 for functional safety (per IEC 61508) by exida® corporation.